the main / All the repair / Window / How to insert the broken glass in the window

How to insert the broken glass in the window

Let us consider in detail how to replace a broken pane of glass in plastic window and a simple wooden frame, All this can be done with their srukami. If the transom is in a remote place, it is best to start to remove it from its hinges and put on a horizontal surface. When handling the glass, be careful. Do not lay it flat on the floor, not to accidentally come. Prisloniv glass to wall, throw in it a bright cloth or newspaper.

To insert the glass in the window you need:

  • window glass;
  • roulette;
  • štapik;
  • Stameska;
  • hammer;
  • silicone sealant;
  • Nailguns;
  • pliers;
  • a sharp knife;
  • hacksaw.

Order of works

  1. Wear thick leather or cotton gloves. When working with glass is necessary to protect the hands from accidental cuts.
  2. Schedro paste on the glass surface cracked pieces of Scotch, masking tape or duct tape. Expand on the windowsill a few sheets of newspaper, so as not to scratch the paint.
  3. Now you need to clean off or remove the putty bead, whichever, a fixture at the glass in the frame. Putty scrape off with a sharp knife or fine screwdriver. To remove it in those places, where it is dried up and hardened, Tap the handle of a knife or a screwdriver with a hammer. Putty can be softened by hot air from a hair dryer or a soldering iron. Carnations or studs pull out flatКак вставить стекло в окноgubtsami. remove the bead, carefully hooking it with a screwdriver or chisel.
  4. Remove the broken glass out of the frame. Pre lay on the floor or on a table newspaper sheets, they add up the glass shards. Wrap and take out the trash.
  5. Sand the wooden folds in the window frame until smooth. You should not be hanging around the wreckage of nails, puff up lumps of putty or wood burrs. Operate chisel, file and pliers.
  6. Remove the sizes for glass. Measure the internal quantities of purified rebated. diminish by 3 mm from each size. This must be done, the glass does not burst during expansion. Order cutting of glass on your sizes in a special workshop. Measure, how much you will need to bead.
  7. Buy the hardware store in bead and white or clear silicone sealant. If you gently pulled out when removing the glass bead, you can use the old. When buying a sealant pay attention to the instructions on the package. Joinery will undergo greater temperature changes, so that the silicone must be suitable. When using the seal in the box, you will need Nailguns. Either buy a sealant, packaged in syringes, but it is not profitable.
  8. Sawed bead size with a hacksaw with fine teeth. Tamp it as thin window cloves, so that at the location in the frame, Carnations were parallel to the glass.
  9. Promazhte silicone sealant all rebates. Put the lower part of the frame a couple of matches for the gap and set the glass. Gently push it to the frame on all sides, pull out the match.
  10. Prybeyte bead. Bead must be covered with paint. This can be done before you install it into the frame, or at the time of full coloring window.

Video:

Replacing the glass in a plastic box

Now let's see a video about how to replace the one broken glass in a double-glazed PVC windows.

Video:

Video:

Video:

Video:

Share with your friends to vote record

Rate post:
1 Звезда2 Звезды3 Звезды4 Звезды5 Звезд (While no ratings)
Loading...
Do you want to place the information in this or any other article - contact, discuss.

Share your experience in the repair

Your email address will not be published. Required fields are marked *

fifteen − 4 =